Equipoise Boldenone Undecylenate 200mg/ml Injections for Lean Muscle Gains
Boldenone Undecylenate/EQ200 Conversion Recipe:
|Boldenone Undecylenate 200mg/ml وصفه:
Equipoise 200mg/ml ……50ml
10g Boldenone Undeclynate Powder
7.5ml of Benzyl Benzoate
2.5ml of Benzyl Alcohol
32ml of your favourite Oil
Boldenone Undecylenate/EQ200 الوصف:
Boldenone Undecylenate, often called Equipoise is an injectable anabolic steroid, derivate of
Testosterone with high anabolic and androgenic properties. The compound is used by bodybuilders and athletes to increase the protein synthesis in the muscle cells, as well as nitrogen retention and appetite. Boldenone Undecylenate also stimulates the release of erythropoietin in the kidneys.
The drug has a very long half-life due to the undecylenate ester and has the ability to offer the muscle quality gains with minimal damage. It is often combined with non-aromatizable steroids such as Trenbolone Acetate, Halotest, orStanozolol, as well as with Testosterone compounds for a stronger effect in muscle mass increase. In order to restore body’s normal functions after long lasting cycles Boldenone Undecylenate has to be combined with HCG and Clomid/Nolvadex.
Dosage and Side Effects Average dosage of Boldenone Undecylenate is 300 – 500 mg per week for men and 50 – 100 mg per week for women. The injection should be administrated at least once every week and the length of a cycle is varies from 7-8 weeks to 10-12 أسابيع. Side effects are mild and occur in mainly in cases of high dosages. Athletes may experience acne, oily skin, hair loss, diarrhea, hypertension, prolonged blood clotting time, increased libido as well as post-menopausal bleeding, increased sex drive, swelling of the breasts and virilization symptoms in women.
The Steps To Make Equipoise 200mg/Ml:
|1: Take out scale (i like to calibrate it every use) and put on unsterile 50ml vial on scale and zero out.
2: Draw up 12ml of Eq using 12ml syringe, make sure there are no airbubbles and plunger is exactly in line with 12ml hatch mark. Now slowly squirt eq into vial until scale says 10.0 grams. For me this is usually exactly 10ml so 1g has 1 mL displacement. Also add the 7.5ml of bb and 2.5ml of ba
3: Now add 30 of the 32ml of oil into the vial to make total volume of oil/ba/bb/hormone to be 50 mL. Leave the 2ml of oil in syringe for later use. Put rubber stopper into vial as well as one of the 18ga needles. Boil a pot of hot water and then remove from heat and put vial into pot for 10 دقيقة, take out after 5 to shake and put back in.
4: I have a crimper so i crimp another seal on the vial but you could also duct tape it on so that rubber
stopper doesn’t come out when upside down when you’re drawing oil out of vial. Here’s what it looks like unfiltered but mixed up.
5: Now take out sterile 50ml vial and wipe stopper with rubbing alchol. Put 18ga needle and 25ga needle through stopper, and attach whatman filter to the 18ga needle stuck in vial.
6: Once you’ve filtered all 50ml and vial is totally empty, take the last 2ml you had saved and run it through the filter to get all gear out of it and only leave plain oil in the filter. This is what final product will look like. Notice i left 25ga pin in.
7: Once you’ve filtered all 50ml and vial is totally empty, take the last 2ml you had saved and run it through the filter to get all gear out of it and only leave plain oil in the filter. This is what final product will look like. Notice i left 25ga pin in.
8: Now put vial in oven at 200 degrees F, and bake for 15 دقيقة. Some repeat this step more than once but i never have and not had a problem. There you go, save yourself a ton of cash and MAKE YOUR OWN GEAR!