Cómo homebrew enantato de testosterona
Hacer tu propio homebrew enantato de testosterona o bien puede simple o complicado, la manera que usted elija para ser. Mucha gente puede desalentarte con mucha de la ciencia en, pero se presentará más simplemente. Aquí están los requisitos y una guía paso a paso sobre cómo puede colar enantato de testosterona
Requirements Ingredients
1.Polvo de enantato de testosterona: 62.5 gramos
2.Enantato de testosterona :250mg / ml
3.Alcohol bencílico(BA): 5ml (2%)
4.Benzoato de bencilo (BB): 50 ml (20ml)
5.Aceite de uva: 148.13ml
Herramientas necesarias
1.Arrugador de mano
2.Diez sistemas viales cada uno con 10 ml (El conjunto debe contener una gorra, tapón de goma, y el frasco.)
3.22Um filtro de jeringa
4.20mL /60 jeringa de ml que tiene un 18-21 aguja de calibre.
5.3jeringa mL con un 18-21 aguja de calibre
6.Una sartén
7.Varilla de vidrio y vaso de precipitados de 100mL
8.Varios pedazos pequeños de papel
9.Una balanza digital (+-0.1 o 0.01)
Pasos específicos para la fabricación de enantato de testosterona
Paso 1: Pesar el polvo de enantato de testosterona.
Paso 2: Agregar el polvo, BA, y BB en el vaso
Paso 3: Calentar el vaso en un baño de agua
Paso 4: Agregar el aceite de semilla de uva
Paso 5: Filtrado de
Paso 6: Prensar con el tirón de los casquillos
Aquí están los pasos detallados sobre cómo se debe hacer;
Paso 1: Pesar el polvo de enantato de testosterona
Weigh the Testosterone Enanthate powder to ensure that you are using the exact quantity that you need to make your homebrew. To get the precise weight, get a small piece of paper and place it on the scale. (Editado por Hongxipharm)
To ensure that you do not include the weight of the paper when weighing the powder, press tare to set the scale to zero. You can now add the powder slowly to avoid placing too much that you may need to keep removing.
A veces el polvo puede pesar tan poco que podría necesitar mantenerlo reajuste cada vez que necesite añadir algunos. La mejor manera de hackearlo es añadiendo un poco de polvo entonces oprima en la escala con el dedo y deje que el número caer detrás. Una vez que estés seguro de que pesar su 25 gramos con exactitud, Ahora estás listo. Weigh the Testosterone Enanthate powder to ensure that you are using the exact quantity that you need to make your homebrew
Paso 2: Agregar el polvo, BA, y BB en el vaso
1.Coloque el polvo pesado en un vaso de precipitados.
2.Añadir 2ml de Alcohol bencílico y benzoato de bencilo 2ml.
La función principal de la adición de Alcohol bencílico es actuar como un agente de esterilización. It also works well as a solvent hence keeping all the oils and powders in one place. Benzyl Alcohol is also a widely used solvent, and the advantage that comes with it is that it aids in having a painless injection.
Paso 3: Calentar el vaso en un baño de agua
This step is optional, but if you want the process to run smoothly, then you shouldn’t skip it. Get a pot and fill it with about an inch of water. Place it on a source of heat, por ejemplo, stove and let it heat. (Editado por Hongxipharm)
Take a pan and put the beaker into it. Place the pan into a few centimeters of water. Keep an eye on the powder and watch as it dissolves until it gets close to clear. A clear solution means that the mixture is now melted.
All this contributes to dissolving the powder entirely into the solvents. Move to the next step when no powder is visible.
Paso 4: Agregar el aceite de semilla de uva
Wait for the concoction to cool down a little then add the grapeseed oil into it. You can then warm it up a little to make filtering easier.
Grape seed oil is the mother of all other oils that act as carriers. Qué es mejor para el uso que otros es que es más delgado y tiene propiedades anestésicas. Además, ayuda a reparar tejido dañado y en definitiva todo es saludable para usted! No es probable que sufren de una reacción alérgica causada por el aceite de semilla de uva.
Paso 5: Filtrado de
El siguiente paso que debe realizar es elaborar la solución en una jeringa que se utiliza para filtrar con. You could use one large syringe or a smaller one and choose to repeat the process multiple times. (Editado por Hongxipharm)
Unwrap the 0.22um syringe filter from its package then fix the green needle on the smaller side and apply to the syringe. Using an alcohol swab, wipe the top of the sterile vial and insert the green needle in it. Place the needle that is attached to the syringe filter into the vial.
This step is a very crucial step, and all finished steroids must go through it. It is normal that the filter may get blocked during the filtration process. Como un resultado, you will notice that the process becomes slow drastically. To counter this, replace the filter with a new one to save you the pain of having to keep waiting.
You, sin embargo, need to note that the time taken to filter a solution depends on the steroid as well as the mg/ml of the product. (Editado por Hongxipharm)
Once you are done filtering in the sterile vial, the process is complete.
Paso 6: Prensar con el tirón de los casquillos
Seal your solution using flip-off caps.
High-quality raw materials, careful operation, production of assured products.
Hongxi Pharm equipo
Todos los derechos reservados