Injectable Anabolic Steroid Testosterone Enanthate 250mg/ml Semi-finished
Testosterone Enanthate(Enanject) Homebrew Recipes(Lab Supply):
Testosterone Enanthate 1000ml @250mg/ml Recipe
250gram Testosterone Enanthate Powder
20mL Benzyl Alcohol BA
180mL Benzyl Benzoate BB
575mL Grapesead Oil
Testosterone Enanthate(Enanject) Powder Info:
Testosterone Enanthate Injection Oil: Testosterone Enanthate 250mg/ml
Testosterone Enanthate Active Ingredient: Testosterone Enanthate
Testosterone Enanthate CAS No: 315-37-7
Testosterone Enanthate Administration: Testosterone is administered in injectable form.
Testosterone Enanthate Active Life: 8 days
Testosterone Enanthate Detection Time: 3 months
Testosterone Enanthate Anabolic/Androgenic Ratio: 100/100
Testosterone Enanthate(Enanject) Description:
Testosterone enanthate injection USP, provides testosterone enanthate, a derivative of the primary endogenous androgen testosterone, for intramuscular administration. In their active form, androgens have a 17-beta-hydroxy group. Esterification of the 17-beta-hydroxy group increases the duration of action of testosterone; hydrolysis to free testosterone occurs in vivo. Testosterone esters are less polar than free testosterone. Testosterone esters in oil injected intramuscularly are absorbed slowly from the lipid phase; thus Testosterone Enanthate can be given at intervals of two to four weeks.
Testosterone Enanthate, once injected, the testosterone does not become active until the ester begins to detach from the hormone. The total detachment does not happen all at once but allows for a slow, steady release of the active hormone into the body. Once injected, there will be a sharp spike in testosterone within the first 24-48 hours post injection. From here the hormone will continually separate and dissipate through the body. By its time frame, Testosterone Enanthate carries a half-life of approximately 8 days, which will allow for as little as one injection every 2 weeks in a therapeutic setting. However, every 7-10 days will prove far more effective in maintaining stability.
Testosterone Enanthate is a single large ester base testosterone compound. This is a pure synthetic testosterone hormone that has a carboxylic acid ester attached in Enanthate (enanthoic acid). The ester itself is attached to the hormone at the 17-beta hydroxyl group. By attaching the Enanthate ester, this allows for a control of the hormones active duration and total release time.
Testosterone Enanthate(Enanject) Injection for Bodybuilding
* Enhanced Protein Synthesis
* Enhanced Nitrogen Retention
* Increased Red Blood Cell Count
* Increased IGF-1 Output
* Inhibition of Glucocorticoids
Testosterone Enanthate(Enanject) Dosage and Administration:
Testosterone enanthate is currently the most widespread and the most popular steroid because it is effective. Large dosages are affordable. Usually, they come in 10 ml vials. A beginner can safely and effectively begin from 250mg every week , while the upper range can go around 1000 mg.In one study, it was found that 600 mg per week produced much better results than the administration of a lower dose. However, it needs to be cautioned that the dose is dependent on several factors and your doctor is the best person to recommend the appropriate dose suitable for you.
Most people have found that a dose within 500 mg to 1000 mg is sufficient enough to build tons of muscles in their body. However, if you are going to use over 500mg of testosterone per week, you must weigh the risk factors in consultation with your private clinician.
How to make Testosterone Enanthate(Enanject) 250mg/ml Oil?
Step 1: Put Testosterone Enanthate powder into the beaker
Step 2: Put BA into the beaker
Step 3: Put BB into the beaker
Step 4: Put the beaker on the heater, temperature is about 80 ºC. Use the glass rod to stir the liquid until the powder dissolves into the liquid totally, then it will be transparent yellow liquid
Step 5: Get the beaker down from the heater, wait until the transparent yellow liquid is cool
Step 6: Put the EO into the beaker, Use the glass rod to stir the liquid until it is transparent yellow liquid again.
Step 7: Filter the liquid with a sterile filter or a filtering machine