Фармацевтической Hongxi – Homebrew Путеводитель

(Our lab operators are preparing liquid in our lab.)

General Guide for Homebrewing: http://www.sarmsteroid.com/lab-service/homebrew-guide/
View more cooking tips: http://www.sarmsteroid.com/news-support/
Buy liquid steroid: http://www.sarmsteroid.com/steroid-liquid/

How To Get Finished Injectable From Raw Steroid Powder:

Firstly mix Steroid powder and BA and BB, you need let this three product complete dissolution and you can see the liquid is clear, very very clear and couldn’t see any crystallization when you disslove this three product, you can heating the liquid can cause the solution to dissolve faster and more fully pls don’t let any water in to liquid until powder dissloved on BA and BB, when this time the liquid must very clear, finally you can add grape seed oil.

After you add oil, fully stirring, at the end of the container to observe, until the liquid temperature is completely cooled to room temperature, if you see the liquid is still clear, so now you have got the semi-finished product is pre-mix injectable.

After you get the pre-mix Injectable, at the end of the container to observe, until the liquid temperature is completely cooled to room temperature, if you can see the liquid is still clear, finally you need filter the liquid by Needle type filter after filter, the product is really means finished product

 

Five Advantages of Making Finished Steroids:

1. The cost is only 40-60% of the normal cost

2. They take only a short time to prepare

3. They are easier and cheaper to ship than amps or vials

4. Less chance of your order getting seized by customs

5. Unlike vials and amps, they come with a refund/reship policy

We can not only supply raw steroids powder, but also semi-finished liquid steroids.

We can help you make your brand, come on and join us!

 

Details Steps to Make Steroid Liquid:

1. Weigh the powder.

2. Place this powder into the glass beaker.

3. Add the the oil into the other glass beaker using the 50mL syringe and heat it in a bath of hot water(80*C). (Под редакцией Hongxi Фарм)

4. Transfer this oil into the beaker with the powder.

5. Use the 3mL syringe to measure your BA and then add it to the oil

6. Use the 10mL syringe to measure your BB and then add it to the oil

7. Stir this mixture with a glass rod or with an 18g needle

8. When fully dissolved, draw as much as you can into the 50mL syringe and then attach the syringe filter to it and then an 18g sharp needle to the end of the filter unit.

9. Swab the top of your sealed vial with an alcohol pad and insert the 25g-27g needle into the vial. This will act as a vent.

10. Now insert the syringe/filter unit into the vial and begin filtering.

11. NEVER draw backwards through the filter, it will destroy it.

12. You may need to unattached the syringe from filter unit(leave the unit still in the vial) and draw the

rest of the AAS/oil mixture into the syringe then re-attach it and proceed to filter it.

13. Once all the oil is filter through, unattached the syringe from the filter unit and draw in 50mL of air. Re-attach it and push this air though. This will get every last drop of the oil out of the filter membrane.

14. Remove the syringes from the vial. Your finished.

15. Now observe this for a day or two to see if it crashes. If not then your good to go.

 

An Example To Make Boldenone Undecylenate(Equipoise) 200мг/мл:

1: Take out scale and put on unsterile 50ml vial on scale and zero out.

2: Draw up 12ml of Eq using 12ml syringe, make sure there are no airbubbles and plunger is exactly in line with 12ml hatch mark. Now slowly squirt eq into vial until scale says 10.0 грамм. For me this is usually exactly 10ml so 1g has 1 mL displacement. Also add the 7.5ml of bb and 2.5ml of ba

3: Now add 30 of the 32ml of oil into the vial to make total volume of oil/ba/bb/hormone to be 50 mL. Leave the 2ml of oil in syringe for later use. Put rubber stopper into vial as well as one of the 18ga needles. Boil a pot of hot water and then remove from heat and put vial into pot for 10 минут, take out after 5 to shake and put back in.

4: I have a crimper so i crimp another seal on the vial but you could also duct tape it on so that rubber stopper doesn’t come out when upside down when you’re drawing oil out of vial. Здесь ’ s это выглядит нефильтрованное, но смешанные вверх.

5: Now take out sterile 50ml vial and wipe stopper with rubbing alchol. Поставьте 18ga иглы и 25ga иглы через пробку, и прикрепите ватман фильтр к 18ga иглы, застрял во флаконе.

6: Once you’ve filtered all 50ml and vial is totally empty, take the last 2ml you had saved and run it through the filter to get all gear out of it and only leave plain oil in the filter. This is what final product will look like. Notice i left 25ga pin in.

7: Once you’ve filtered all 50ml and vial is totally empty, take the last 2ml you had saved and run it through the filter to get all gear out of it and only leave plain oil in the filter. This is what final product will look like. Notice i left 25ga pin in.

8: Now put vial in oven at 200 degrees F, and bake for 15 минут. Some repeat this step more than once but i never have and not had a problem.

There you go, save yourself a ton of cash.

NOW YOU CAN MAKE YOUR OWN GEAR AND BRAND!

Send Inquiry: http://www.sarmsteroid.com/inquiry/
Welcome Inquiry and Business Cooperation!

  • Служба лаборатории

  • Тестостерон стероиды Смесь стероидов Инъекционные стероиды Пептид Boldenone нефти Устные стероиды SARMs порошок Нандролон порошок Стероидных жидкости Стероидных порошок Стероидные гормоны Стероидных поставщика Тренболон стероидов SARMs Тестостерон энантат
  • Свяжитесь с нами

  • Company Superiority

    1. Highest Quality Guarantee
    2. Lowest Price Guarantee
    3. Analysis Report Guarantee
    4. Fresh Batch Guarantee

  • Latest News

  • Новейшие продукты