Wie man Testosteron Enanthate homebrew

Wie man Testosteron Enanthate homebrew

Making your own homebrew Testosterone Enanthate can either be simple or complicated, the way you choose it to be. A lot of people may discourage you with a lot of science in it, but we will present it more simply. Here are the requirements and a step by step guide on how you can brew Testosterone Enanthate

Requirements Ingredients

1.Testosteron Enanthate Pulver: 62.5 Gramm

2.Testosteron Enanthate :250mg per ml

3.Benzylalkohol(BA): 5ml (2%)

4.Benzylbenzoat (BB): 50 ml (20ml)

5.Traubenkernöl: 148.13ml

Tools needed

1.Hand crimper

2.Ten sets Vials each having 10 ml (The whole set should contain a cap, rubber stopper, and the vial.)

3.22um Syringe filter

4.20ml /60 ml syringe that has an 18-21 Messnadel.

5.3mL syringe with an 18-21 Messnadel

6.A frying pan

7.Glass Rod and 100mL Beaker

8.Several small pieces of paper

9.A digital scale (+-0.1 oder 0.01)

Specific steps for making testosterone enanthate

schritt 1: Weigh testosterone enanthate powder.

schritt 2: Add powder, BA, and BB into the beaker

schritt 3: Heat the beaker in a water bath

schritt 4: Add grapeseed oil

schritt 5: Filternd

schritt 6: Crimp them with flip off caps

Here are the detailed steps on how it should be done;

schritt 1: Weigh testosterone enanthate powder

Weigh the Testosterone Enanthate powder to ensure that you are using the exact quantity that you need to make your homebrew. To get the precise weight, get a small piece of paper and place it on the scale. (Herausgegeben von Hongxipharm)

To ensure that you do not include the weight of the paper when weighing the powder, press tare to set the scale to zero. You can now add the powder slowly to avoid placing too much that you may need to keep removing.

Sometimes the powder may weigh so little that you may need to keep resetting it every time you need to add some. The best way to hack it is by adding a little powder then press on the scale using your finger and allow the number to fall back down. Once you are sure that you have weighed your 25 grams accurately, you are now good to go. Weigh the Testosterone Enanthate powder to ensure that you are using the exact quantity that you need to make your homebrew

schritt 2: Add powder, BA, and BB into the beaker

1.Place the weighed powder into a beaker.

2.Add 2ml of Benzyl Alcohol and 2ml Benzyl Benzoate.

The primary function of adding Benzyl Alcohol is to act as a sterilizing agent. It also works well as a solvent hence keeping all the oils and powders in one place. Benzyl Alcohol is also a widely used solvent, and the advantage that comes with it is that it aids in having a painless injection.

schritt 3: Heat the beaker in a water bath

This step is optional, but if you want the process to run smoothly, then you shouldn’t skip it. Get a pot and fill it with about an inch of water. Place it on a source of heat, zum Beispiel., stove and let it heat. (Herausgegeben von Hongxipharm)

Take a pan and put the beaker into it. Place the pan into a few centimeters of water. Keep an eye on the powder and watch as it dissolves until it gets close to clear. A clear solution means that the mixture is now melted.

All this contributes to dissolving the powder entirely into the solvents. Move to the next step when no powder is visible.

schritt 4: Add grapeseed oil

Wait for the concoction to cool down a little then add the grapeseed oil into it. You can then warm it up a little to make filtering easier.

Grape seed oil is the mother of all other oils that act as carriers. What makes it better for use than others is that it is thinner and has anesthetic properties. Auch, it helps repair damaged tissue and to sum it all it is healthy for you! You are not likely to suffer from an allergic reaction caused by grape seed oil.

schritt 5: Filternd

The next step you should undertake is to draw up the solution into a syringe that you will use to filter with. You could use one large syringe or a smaller one and choose to repeat the process multiple times. (Herausgegeben von Hongxipharm)

Unwrap the 0.22um syringe filter from its package then fix the green needle on the smaller side and apply to the syringe. Using an alcohol swab, wipe the top of the sterile vial and insert the green needle in it. Place the needle that is attached to the syringe filter into the vial.

This step is a very crucial step, and all finished steroids must go through it. It is normal that the filter may get blocked during the filtration process. Als Ergebnis, you will notice that the process becomes slow drastically. To counter this, replace the filter with a new one to save you the pain of having to keep waiting.

You, jedoch, need to note that the time taken to filter a solution depends on the steroid as well as the mg/ml of the product. (Herausgegeben von Hongxipharm)

Once you are done filtering in the sterile vial, the process is complete.

schritt 6: Crimp them with flip off caps

Seal your solution using flip-off caps.

High-quality raw materials, careful operation, production of assured products.

Hongxi Pharm Team
Alle Rechte vorbehalten