Injectable Anabolic Steroid Testosterone Enanthate 250mg/ml Semi-finished
Enantato de testosterona(Enanject) Homebrew Recetas(Suministro de laboratorio):
Testosterone Enanthate 1000ml @250mg/ml Recipe
250gram Testosterone Enanthate Powder
20mL Benzyl Alcohol BA
180mL Benzyl Benzoate BB
575mL Grapesead Oil
Enantato de testosterona(Enanject) Polvo Información:
Testosterone Enanthate Injection Oil: Enantato de testosterona 250mg/ml
Testosterone Enanthate Active Ingredient: Enantato de testosterona
Testosterone Enanthate CAS No: 315-37-7
Testosterone Enanthate Administration: Testosterone is administered in injectable form.
Testosterone Enanthate Active Life: 8 días
Testosterone Enanthate Detection Time: 3 meses
Testosterone Enanthate Anabolic/Androgenic Ratio: 100/100
Enantato de testosterona(Enanject) Descripción:
Testosterone enanthate injection USP, provides testosterone enanthate, a derivative of the primary endogenous androgen testosterone, for intramuscular administration. In their active form, androgens have a 17-beta-hydroxy group. Esterification of the 17-beta-hydroxy group increases the duration of action of testosterone; hydrolysis to free testosterone occurs in vivo. Testosterone esters are less polar than free testosterone. Testosterone esters in oil injected intramuscularly are absorbed slowly from the lipid phase; thus Testosterone Enanthate can be given at intervals of two to four weeks.
Enantato de testosterona, once injected, the testosterone does not become active until the ester begins to detach from the hormone. The total detachment does not happen all at once but allows for a slow, steady release of the active hormone into the body. Once injected, there will be a sharp spike in testosterone within the first 24-48 hours post injection. From here the hormone will continually separate and dissipate through the body. By its time frame, Testosterone Enanthate carries a half-life of approximately 8 días, which will allow for as little as one injection every 2 weeks in a therapeutic setting. Sin embargo, every 7-10 days will prove far more effective in maintaining stability.
Testosterone Enanthate is a single large ester base testosterone compound. This is a pure synthetic testosterone hormone that has a carboxylic acid ester attached in Enanthate (enanthoic acid). The ester itself is attached to the hormone at the 17-beta hydroxyl group. By attaching the Enanthate ester, this allows for a control of the hormones active duration and total release time.
Enantato de testosterona(Enanject) Inyección para Culturismo
* Síntesis de la proteína mayor
* Retención de nitrógeno mayor
* Conteo de glóbulos rojos aumento
* Increased IGF-1 Output
* Inhibición de los glucocorticoides
Enantato de testosterona(Enanject) Dosage and Administration:
Testosterone enanthate is currently the most widespread and the most popular steroid because it is effective. Large dosages are affordable. Generalmente, they come in 10 viales de ml. A beginner can safely and effectively begin from 250mg every week , while the upper range can go around 1000 mg.In one study, it was found that 600 mg per week produced much better results than the administration of a lower dose. Sin embargo, it needs to be cautioned that the dose is dependent on several factors and your doctor is the best person to recommend the appropriate dose suitable for you.
Most people have found that a dose within 500 mg a 1000 mg is sufficient enough to build tons of muscles in their body. Sin embargo, if you are going to use over 500mg of testosterone per week, you must weigh the risk factors in consultation with your private clinician.
How to make Testosterone Enanthate(Enanject) 250mg/ml Aceite?
Paso 1: Put Testosterone Enanthate powder into the beaker
Paso 2: Pon BA en el vaso de precipitados
Paso 3: Pon bb en el vaso de precipitados
Paso 4: Pon el vaso de precipitados en el calentador, la temperatura es aproximadamente 80 º C. Use la varilla de vidrio para remover el líquido hasta que el polvo se disuelva totalmente en el líquido, entonces será líquido amarillo transparente
Paso 5: Baja el vaso del calentador., esperar hasta que el líquido amarillo transparente esté fresco
Paso 6: Pon la EO en el vaso de precipitados, Use la varilla de vidrio para remover el líquido hasta que vuelva a ser líquido amarillo transparente.
Paso 7: Filtrar el líquido con un filtro estéril o una máquina filtrante